FGK型转鼓式造粒机具有以下特点:
1:利用通入蒸汽或料浆的方法,提高造粒物料温度,减低造粒水分,减少干燥负荷,提高整机产量。
2:热造粒可提高颗粒强度,一般平均颗粒强度>10牛顿,热造粒对养分配比调整的适应性更强,特殊结构有利于提高颗粒的圆润程度。
3:成粒率一般可达85%以上。
4:操作弹性大,动力消耗省,维修费用低。
5:用工程塑料内衬可起到自身清理筒壁粘料和清理方便的作用,并同时起到防腐保温作用
The Model FGL recolving drum granulator exhibits the following featurea
1.By the introduction of steam or slurry of granulating material is raised, the moisture for granulation decreased, and the clrying load reduced, thus increasing the output of the granulator.
2.Hot granulation in creased the strength of the granules, which havee generally a strength of more than ION on the averge. Hot granulation is more adaptable to the adjustment of mutrient ratio, and the special structure is favorable to an improvement or roundness of the granules.
3.The granulation ration is about 85%
4.Operation is flexible, power consumption and maintenance cost low.
5.The use of engeerousing plastics as lining results in self-cleaning of the material adhered on the shell wall and convenience in clean u as well as resistance to corrosion and preservation.
型号 | 主要参数 m |
转速 r/min |
生产能力 T/h |
物料水分% 进口水分 |
温度℃ 进口水分 |
功率 KW |
倾角° | 外形尺寸长×宽×高 水平放置(mm) |
备注 |
---|---|---|---|---|---|---|---|---|---|
FGL15-2600 | 2.6×10 | 8.0 | 30-50 | 8-10% | 60-90/ 4-8% |
55 | 1.5±0.3 | 12500×4900×5200 | 内衬塑料 板聚丙烯 或不锈钢 |
FGL10-2400 | 2.4×10 | 8.0 | 25-45 | 45 | 1.5±0.3 | 12500×4400×5000 | |||
FGL10-2200 | 2.2×10 | 9.0 | 25-35 | 37 | 1.5±0.3 | 11200×3180×2980 | |||
FGL8-2000 | 2.0×8 | 9.0 | 20-25 | 30 | 2±0.3 | 9850×3030×2860 | |||
FGL5-1800 | 1.8×6 | 11 | 9.0-12 | 18.5 | 2±0.3 | 8800×2805×2780 | |||
FGL3-1500 | 1.5×5 | 14.7 | 5.0-7.0 | 11 | 2±0.3 | 5600×2510×2378 | |||
FGL2-1200 | 1.2×5 | 13 | 3.0-5.0 | 7.5 | 2±0.3 | 5550×2207×1936 | |||
FGQ1-1200 | 1.2×4.5 | 13 | 1.5-2.5 | 5.5 | 2±0.3 | 5040×2207×1936 |